Inverters

Exeltech XP250 48 Volt

$598.00

In stock

SKU: EXE0004

Free Shipping!


Exeltech’s XP series inverters provide the cleanest, best regulated sine wave output over the widest DC input of any inverter on the market today.

Details

  • DC INPUTS: A two-pole connector is provided under the rear cover. The rear cover must also be removed to access this connector. A 2 pole female connector is provided.
  • “REMOTE” CONNECTION: This is on the six-pole, plug-in connector, located under the rear cover.
  • AC OUTPUTS: Has one NEMA-15 outlet (standard wall receptacle), located on the front panel. Additionally, it can be hardwired to appliance/load using connections furnished on the six-pole, plug-in connector, located under rear cover.
  • 230 VAC: Inverters have an IEC-320 receptacle located on the front panel.
  • COOLING: Convection cooled.
  • DC POWER ON LED: Located on the front panel, will be “ON” when the inverter is powered up and DC power is available.
  • LOW BATT/THERM BUZZER: Produces an audible alarm if DC input voltage falls to a level within 2% to 4% of the low limit of the inverter, or if there is an over-temperature condition.
  • ON/OFF SWITCH: Located on front panel; turns the inverter on and off.
  • OVER VOLTAGE PROTECTION: If input voltage to the inverter exceeds set limits, the inverter will immediately shut off, without warning. When input voltage returns to normal range, the inverter will immediately restart. Since high over-voltages tend to have very fast edges, the inverter must shut down quickly to protect itself. This kind of fault usually occurs if the battery is suddenly disconnected from the system and the battery charger continues to supply current. When battery voltage falls to within 2% to 4% of low line voltage, the LOW BATT/THERM buzzer will sound. If the condition continues without reducing load to the inverter or adding charge to the battery, the inverter will shut off. When voltage rises to approximately 95% of nominal battery voltage, the inverter will turn back on and the alarm condition will clear. The inverter can be manually reset by cycling the on/off switch. This will reset the protection circuitry and turn the inverter on at any voltage above minimum voltage.
  • OVER TEMPERATURE PROTECTION: The inverter is also protected against overheating. It will provide its full rated output up to the temperature listed in the specification sheet. If it is subjected to higher ambient temperatures, or air circulation is blocked, the inverter could overheat. If the LOWBATT/THERM buzzer sounds, immediate action is required or the inverter will shut down. Either reduce load, or provide more cooling in the immediate environment. If no action is taken, the inverter will likely shut down with in two minutes. When the inverter shuts down, the alarm condition will persist. Since the inverter has eliminated its load, it will quickly cool. It will automatically restart when it has cooled sufficiently, and the LOW BATT/THERM alarm will clear. If the internal temperature is over 105C° a warning buzz of 5 C° will commence before shut off.
Surge Power: 1100 W
Output DC Voltage: 48 Volts DC
Output Current: 6.1 A
Output power Type: Pure sine wave
Inverter type: Grid-Tied
Weight: 7
  1. Be the first to review this product

WRITE YOUR REVIEW

Write Your Own Review

You're reviewing: Exeltech XP250 48 Volt

How do you rate this product? *

  1 star 2 stars 3 stars 4 stars 5 stars
Quality

Features

Details

  • DC INPUTS: A two-pole connector is provided under the rear cover. The rear cover must also be removed to access this connector. A 2 pole female connector is provided.
  • “REMOTE” CONNECTION: This is on the six-pole, plug-in connector, located under the rear cover.
  • AC OUTPUTS: Has one NEMA-15 outlet (standard wall receptacle), located on the front panel. Additionally, it can be hardwired to appliance/load using connections furnished on the six-pole, plug-in connector, located under rear cover.
  • 230 VAC: Inverters have an IEC-320 receptacle located on the front panel.
  • COOLING: Convection cooled.
  • DC POWER ON LED: Located on the front panel, will be “ON” when the inverter is powered up and DC power is available.
  • LOW BATT/THERM BUZZER: Produces an audible alarm if DC input voltage falls to a level within 2% to 4% of the low limit of the inverter, or if there is an over-temperature condition.
  • ON/OFF SWITCH: Located on front panel; turns the inverter on and off.
  • OVER VOLTAGE PROTECTION: If input voltage to the inverter exceeds set limits, the inverter will immediately shut off, without warning. When input voltage returns to normal range, the inverter will immediately restart. Since high over-voltages tend to have very fast edges, the inverter must shut down quickly to protect itself. This kind of fault usually occurs if the battery is suddenly disconnected from the system and the battery charger continues to supply current. When battery voltage falls to within 2% to 4% of low line voltage, the LOW BATT/THERM buzzer will sound. If the condition continues without reducing load to the inverter or adding charge to the battery, the inverter will shut off. When voltage rises to approximately 95% of nominal battery voltage, the inverter will turn back on and the alarm condition will clear. The inverter can be manually reset by cycling the on/off switch. This will reset the protection circuitry and turn the inverter on at any voltage above minimum voltage.
  • OVER TEMPERATURE PROTECTION: The inverter is also protected against overheating. It will provide its full rated output up to the temperature listed in the specification sheet. If it is subjected to higher ambient temperatures, or air circulation is blocked, the inverter could overheat. If the LOWBATT/THERM buzzer sounds, immediate action is required or the inverter will shut down. Either reduce load, or provide more cooling in the immediate environment. If no action is taken, the inverter will likely shut down with in two minutes. When the inverter shuts down, the alarm condition will persist. Since the inverter has eliminated its load, it will quickly cool. It will automatically restart when it has cooled sufficiently, and the LOW BATT/THERM alarm will clear. If the internal temperature is over 105C° a warning buzz of 5 C° will commence before shut off.

Specifications

Surge Power: 1100 W
Output DC Voltage: 48 Volts DC
Output Current: 6.1 A
Output power Type: Pure sine wave
Inverter type: Grid-Tied
Weight: 7

Reviews

  1. Be the first to review this product

WRITE YOUR REVIEW

Write Your Own Review

You're reviewing: Exeltech XP250 48 Volt

How do you rate this product? *

  1 star 2 stars 3 stars 4 stars 5 stars
Quality

Make An Offer

We are often running unadvertised sale prices, rebates & special offers. We invite you to make a reasonable counter-offer at any time for any item. Who knows? - this may be your lucky day! We'll do our best to help you any way we can.